Brake Upgrade Kits

308mm one piece S2 Brake discs. These 308mm brake discs have curved vanes which are handed left and right to ensure balanced cooling accross both sides of the car, unlike the original 288mm discs which use one casting and have curved vanes all in the same direction. This leads to one side of the cars brakes being cooled better than the other!!! Many of the aftermarket discs that are available also use one casting with vanes which are in one direction only! Then they have grooves or holes put onto the disc to make them handed. These discs use handed castings and should not be confused with other products on the market. These discs are as used on the Europa SE and 2010 Exige with the factory fitted fast road brake kit!! Could be used as part of a front brake upgrade on a standard S2 VX220 or Europa, using the standard 2 pot calipers, spacers and the correct length caliper retaining bolts Diameter = 308mm Thickness = 26mm Braking surface = Drilled Disc type = Vented Vanes = Curved, handed left and right Learn More

Exige V6 332mm Alcon Brake Kit Consisting of :- 2 x 332mm x 32mm Front brake disc rota's 2 x Floating bell kits (Front) Including titanium bobbins, anti-rattle clips, nuts and bolts 2 x 332mm x 26mm Rear brake disc rota's 2 x Rear brake bells including nuts and bolts Brake pads as an option Ferodo 2500 Pagid RS29 Performance friction The front discs are assembled with fully floating bells and are also fitted with anti rattle clips. (Also available with a fixed bell-see options below) To stop the noises usually associated with floating bells we supply the kit with the anti-rattle clips as shown. Learn More

Exige V6 332mm Alcon Front disc with Floating Bells These floating brake discs are a direct replacement for the standard 332mm front disc on the Exige V6. Each fit contains the following parts 2 x 332 x 32mm Alcon discs 2 x Floating bells 24 x titanium drive bobbins 24 x nut/bolt fittings 12 x disc anti rattle clips. The anti rattle clips stop the 'clatter' usually found with floating bells Priced and sols as a pair of discs Learn More

Exige V6 343mm Alcon Front disc with Floating Bells These floating 343mm brake discs are a direct replacement for the standard 332mm front disc on the Exige V6. Each fit contains the following parts 2 x 343 x 32mm Alcon discs 2 x Floating bells 24 x titanium drive bobbins 24 x nut/bolt fittings 12 x disc anti rattle clips. 4 x caliper spacers The anti rattle clips stop the 'clatter' usually found with floating bells Priced and sold as a pair of discs Learn More

Exige V6 343mm Big Brake Kit Consisting of :- 2 x 343mm x 32mm Front brake disc rota's 2 x Floating bell kits (Front) Including titanium bobbins, anti-rattle clips, nuts and bolts 2 x 343mm x 26mm Rear brake disc rota's 2 x Rear brake bells including nuts and bolts 4 x stainless caliper spacers 2 sets of brake pads. (Same pads front and rear) The standard brake pads offered in this kit are the Ferodo 2500, optionally Performance friction pads are also available (see options below) The front discs are assembled with fully floating bells and are also fitted with anti rattle clips. It is our opinion that discs this large size should be installed with floating bells, To stop the noises usually associated with floating bells we supply the kit with the anti-rattle clips shown. The standard car uses slightly smaller brake pads in the rear, this kit uses the larger front brake pads in both the front and the rear!! Unlike some of the kits available that use the smaller rear pads in the both the front and rear Special attention to wheel weigh position is required on the front wheels with this brake kit Learn More

Exige V6 Front Floating Bell Upgrade Kit A floating bell upgrade kit for cars already fitted with two piece front brake discs. Designed to be installed with the factory supplied two piece brake rota. The kit consists of the following parts 2 x Alloy floating bells 24 Titanium drive bobbins 24 Nuts / bolts 12 x Anti rattle clips Learn More

Motorsport and safety feature at the same time: Our newly developed Ko-Bra Race ABS and ESP! The 1st available motorsport ABS / ESP on the market especially developed for the Exige and It has and extensively tested. Komo-Tec's many years of experience in motorsport, the knowledge of the Exige range itself and the feedback from customers have made it possible to work and point out the essential points for development and optimization. The result is a genuine plug'n'play solution, It does not require additional sensors and wiring looms, It uses the cars current sensors and wiring. The system is just as suitable for everyday sporting use as it is for ambitious use on the track! The existing Lotus-DPM functions of the driving modes (Tour, Sport, Race and OFF) could be integrated and expanded. So if you make the effort to use the system right, you will definitely be faster and safer! ABS: In the future, the limiting factor for you will (almost) be the choice of tires only! Typical racing deceleration forces ​​of over 2g are possible now! Even when braking deep into the curve, the typical understeering of the standard brake is eliminated and enables precise steering through an optimal ratio between the maximum possible braking and lateral force control. The so-called ice mode (“hard brake pedal”) is prevented. ESP: An ESP works through selective brake intervention and regulation of the engine torque. The lower torque in particular causes a considerable interruption in power. Thanks to our adapted regulation, you control the torque by the accelerator pedal only. The control allows higher drift angles and also power slides. Twists are still effectively prevented and corrected more gently. It is still possible to switch off the ESP completely - but it is no longer necessary for a hot lap time as overcompensating brake interventions no longer take place. EDS: The electronic limited slip differential is no longer activated in the software to relieve the brake on the rear axle and protect it from overheating. However, we recommend a limited slip differential. TC: The traction control is also no longer activated in the software in order to achieve better traction and full access to the engine torque. Variable Settings: A previously unavailable option is added. You can use variable settings via the Lotus Mode selection-button. These can be adapted to the typical tyre types used (road / rain, semi-slick, slick), see pictures. Data recording: All variables relevant to driving dynamics are made available via CAN bus and can be recorded via CAN logger (not included in the offer). This ABS/ESP unit can be used on: Exige V6s, Cup V6, Sport 350, Cup 360, Sport 380, Cup 380, Sport 410, Cup 430 Motorsport part. Price includes installation at our workshop in East Yorkshire (NOT AVAILABLE FOR DELIVERY) Learn More

Goodridge Stainless Brake Hoses (2) 4 Pot Calipers A pair of replacement Goodridge brake hose with stainless ends and fittings for calipers that use a Banjo style fitting For S2 Exige with 4 pot calipers etc etc.( NOT for V6 Exige or Evora) Learn More

Lotus sport developed big brake upgrade for the S2 Elise,Exige This kit consists of the following parts:- AP Racing/Lotus direct fit four pot calipers (No brackets necessary) Matching front and rear brake pads Two one piece handed 308mm discs (4 stud) Four braided brake hoses Caliper mounting bolts DOES NOT INCLUDE BRAKE FLUID This brake kit will fit inside a standard Lotus 16 inch (5.5 wide) wheel but DOES need careful positioning of the wheel balance weights All the major parts needed to upgrade the braking system of an S2, Europa S or VX220 to the same as that fitted to the 2010 Exige with the sport pack brake kit or the Europa SE (Just add brake fluid) Developed by the people who designed the car. Learn More

Seriously Lotus 4 Pot 308mm Brake Upgrade Kit (All S2 Toyota cars) Buy sourcing all the best components from the leading brake manufacturers we have put togarther this very cost effective 4 pot upgrade kit for your S2. Buy using the Lotus - AP racing calipers the correct piston size for the cars brake master cylinder is maintained This kit consists of the following parts:- 2 x AP Racing/ Lotus direct fit four pot calipers (No brackets necessary) Matching front and rear brake pads (Ferodo 2500) 2 x Nitron fixed alloy bells with bolts, 2 x 308mm Alcon 2 x Braided brake hoses Caliper and disc mouting bolts and screws Your car may need the wider Exige S2 size wheels for this kit to fit. This brake kit will NOT fit inside a standard Lotus 16 inch (5.5 wide) wheel. Everything needed to upgrade the braking system of an S2, If you use your car on the track we have added the option of using any of the following brake pad materials as an upgrade Pagid RS4-2 Carbone Lorraine RC5+ Carbone Lorraine RC6 We can also offer Castrol SRF brake fluid. Learn More