Steering

Our own Anti Roll Bar Drop Link as used on all models of Elise,Exige and VX220. Worn and aging Anti Roll Bar Drop Links are a common cause of MOT failure. Made exclusively for Seriously Lotus in Europe (Looks exactly like the genuine Lotus part). Each link comes complete with two self locking nuts (correct fine pitch threads) Equivalent to Lotus part number A111C0063F Learn More

Camber Shim / ABS Bracket S2 / VX220 / 211 / Europa A set of four camber shim ABS brackets as used on all models with Kelsey Hayes ABS system (Elise & Exige S2 / VX220/ 211 / Europa) 2 X LH (Equivalent to Lotus part number B116C0013F) 2 X RH (Equivalent to Lotus part number B116C0012F) Made from stainless steel (0.9mm) Come with new cable tie retaining clips Learn More

Camber Shim / ABS Bracket S3 Elise / V6 Exige A set of two V6 Exige or four S3 Elise camber shim ABS brackets as used on all models with Bosch ABS system LH (Equivalent to Lotus part number A120C4005F) RH (Equivalent to Lotus part number A120C4006F) Made from stainless steel (0.9mm) Comes with new cable tie retaining clips Learn More

Camber Shim / Speed Sensor Bracket S2 K Series One camber shim bracket with speed sensor mount point to secure the speed sensor wire, Normally installed on the Left Rear camber adjustment point Originals are made from mild steel and rust badly, These are stainless steel (0.9MM) Original lotus part number was A117D0071F Learn More

Evora Steering Rack Toe link Rod Parts for the Evora steering rack have been unavailable until now! replacement racks from Lotus are currently £1054.95 inc VAT. A common failure on these racks is the joint at the inner end of the track rod, meaning a replacement rack is needed to pass the MOT At last here is a cost effect repair part for these steering racks, supplied singularly Fits all Evora models including the 400 and 410 Learn More

Horn Contact Ring As used on all Elise, Exige variants before 2007 (non airbag type cars) Lotus part number A111H6008F Learn More

M16 Hub Bolt Kit (S1 & S2) Learn More

Momo Tuner Steering wheel Learn More

Rack height setting plates for lowered cars These items are required if the ride height of your car is lowered by more than a few millimetres. If you lower your suspension, the angle of your steering arm changes in relation to the height of the steering rack i.e. the steering rack track arm is angled upwards. Genuine Lotus Motorsport 10 notch rack setting plates will raise the steering rack by approximately 8mm and help to remove some unwanted bump steer. SUPPLIED IN PAIRS Lotus part number A111H0021F Learn More

The kit supplied includes the following parts Momo tuner steering wheel (320mm) B&G Quick release Steering wheel boss for airbag cars Horn ring for air bag cars Momo horn push Optional Lotus horn push The kit does NOT include an air bag delete, this will need to be sourced by the customer Learn More

The kit supplied includes the following parts Momo tuner steering wheel (320mm) B&G Quick release Steering wheel boss adapter for non airbag cars (uses the original steering wheel boss) (Horn ring to be used from original steering wheel) Momo horn push Optional Lotus horn push Early cars not designed with air bags (S1 and early S2 up to about 2007) Learn More

S1 (Wheel Bearing) Circlip One circlip, Two required per bearing Learn More

S1 Elise/Exige/340R Wheel Hub Flange Equivalent to lotus part number A111C6001F & A111C6021F Made in the UK by OEM supplier from forged EN24 Steel. Learn More

S2/S3 Elise and Exige Steering Rack Toe link Rod Parts for the Elise and Exige Sona steering rack have been unavailable until now! Replacement racks from Lotus are over £700. A common failure on these racks is the joint at the inner end of the track rod, meaning a replacement rack is needed to pass the MOT At last here is a cost effect repair part for these steering racks, supplied singularly (Two require per vehicle) Fits all Elise and Exige models fitted with the Sona steering rack (All Toyota engine Elise and Exige models) Learn More

S2/S3 Sona Steering Rack Service Kit 2 X Steering rack tie rods 2 X Rack boots/Gaitors Plus the option of adding two track rod ends Learn More

A pair of steering rack gaitors for all models of Elise and Exige fitted with the Sona steering rack (All Toyota engine Elise and Exige models) Equivalent to lotus part number A120H6004S A120H6005S These gaitors are a direct replacement for the original parts as used by lotus. They are not an of the shelf part that is larger than the original part Complete with four nylon tie wraps Supplied as a pair Learn More

Steering Arm / Upper plinth Bolt Kit. On the S2 Elise and Exige, Lotus upgraded the bolts that are used in the Steering arms on the front suspension and the Top Ball Joint Plinths on the rear suspension from 8.8 to 10.9. This kit of 10.9 cap head bolts are a must for anyone driving there S2 on the circuit. (The S1 cars with alloy uprights use 8.8 grade bolts for the steering arms and top ball joints) 4 bolts for the two front steering arms 4 bolts for the two rear top ball joint plinths Learn More

Steering Column Lower Shaft and Universal Joints Equivalent to Lotus part number D111H0003F Fits all S1, S2K, S2 Toyota, Europa, etc etc Comes complete with the correct high grade nuts and bolts (3 bolts 3 nuts) Learn More

Two Phosphor Bronze Cups for the Aluminium Steering Rack. The Bronze cups are a direct replacement for the standard Nylon cup, which can fail in extreme cicumstance such as heavy track work with sticky tyres. Learn More

Steering Wheel Adaptor (Non Air Bag Cars) Adaptor boss to allow the fitment of quick release couplings and after market steering wheels to non Air Bag cars. Suits quick release couplings with 70mm x 6 PDC fitment Bolts directly to the original steering wheel boss. Learn More

Steering Wheel Adaptor (boss) as used on the Exige V6 Cup with a removable steering wheel. Will fit all cars with air bags (Also car with Airbags deleted from steering wheel) Can also be used on non air bag cars, without the need to use the original boss from the steering wheel Learn More

Lotus OEM Track Rod End for the Exige V6 and 3Eleven Supplied with the correct fine pitch nyloc nut. Lotus part number B138H0006F Learn More

Track Rod End Lock Nuts A pair of track rod end lock nuts (M12 x 1.25) as used on all Elise and Exige varients Equivalent to lotus part number A111W3124F Learn More