Suspension/Steering

Wishbone Bush Assembly Lubricant P-80 Emulsion is specifically formulated to provide a temporary lubrication for the installation of bushes etc The lubrication properties only work when the lubricant is wet. Learn More

VX220 Toe Link Kit (Tapered Uprights) Learn More

VX220 Toe Link Kit (Earlier Cars With Parallel Uprights) Learn More

A suspension refresh kit consisting of 1x full set of Seriously Lotus wishbone bushes or 1 x set of Superpro suspension bushes 8x Suspension Ball Joints 2x Track Rod Ends (Lotus OEM) 2x Antiroll bar drop links 1x Suspension bolt kit including damper bolts. All the main components required to carry out a suspension refresh. Learn More

Lotus OEM Track Rod End for the S1 S2 Elise, Exige and 211 These are also the Track Rod Ends now supplied by Lotus The original S1 Track Rod End was about 10mm shorter than this one and is no longer available from Lotus. If fitting to an early car with 2 lock nuts on the track rod, remove the thin lock nut, before refitting a single locknut and new track rod end. Supplied with the correct fine pitch nyloc nut. Why buy after market copies when you can have the one as supplied by Lotus Lotus part number ref - A117H0009F. Learn More

Track Rod End Lock Nuts A pair of track rod end lock nuts (M12 x 1.25) as used on all Elise and Exige varients Equivalent to lotus part number A111W3124F Learn More

Lotus OEM Track Rod End for the Exige V6 and 3Eleven Supplied with the correct fine pitch nyloc nut. Lotus part number B138H0006F Learn More

Full or part Nut and Bolt kits for your suspension. Available as either just the 14 suspension pivot piont bolts (the other two use the rear toe link joint) or the 8 damper mounting bolts. Also available as a full kit. Each kit has one nyloc nut and two washers for each bolt. Learn More

A suspension refresh kit consisting of 1x full set of Seriously Lotus wishbone bushes or Superpro bushes. Also available with an upgrade to Nitron inner bearings., 8x Suspension Ball Joints 2x Track Rod Ends (S1 or S2 = OEM) 2x Our own Antiroll bar drop links 1x Suspension bolt kit including damper bolts. All the main components required to carry out a suspension refresh. Learn More

SuperPro Polyurethane Suspension Bushes Suits all models and derivatives of Elise, Exige and VX220 A direct replacement for the factory rubber bushes fitted to the wishbones. Stiffer bushes enhance the handling characteristics of your Lotus by maintaining the same level of hardness irrespective of load in comparison to rubber. The resilience of SuperPro bushings allow them to return to their cast shape after compression allows better control of noise, vibration and hardness in a vehicle. The fine tolerances on the bushings provide better road handling, increased tyre life, more responsive steering, and longer service life of suspension components. The special design of these bushes results in reduced rotational friction Each Kit Contains 32 x Polyurethane bushes (Two in each bush location) 16 x Steel inserts 16 x castor washers Learn More

SuperPro Polyurethane Anti Roll Bar Bushes Suits all models and derivatives of Elise, Exige and VX220 with Alloy ARB mountings and the 19mm Roll Bar A direct replacement for the factory soft rubber bushes fitted to the Anti Roll Bar mountings. Stiffer bushes enhance the handling characteristics of your Lotus by maintaining the same level of hardness irrespective of load in comparison to rubber. The resilience of SuperPro bushings allow them to return to their cast shape after compression allows better control of noise, vibration and hardness in a vehicle. The fine tolerances on the bushings provide better road handling, increased tyre life, more responsive steering, and longer service life of suspension components. Each Kit Contains 2 x Polyurethane bushes Learn More

Steering Wheel Adaptor (boss) as used on the Exige V6 Cup with a removable steering wheel. Will fit all cars with air bags (Also car with Airbags deleted from steering wheel) Can also be used on non air bag cars, without the need to use the original boss from the steering wheel Learn More

Steering Wheel Adaptor (Non Air Bag Cars) Adaptor boss to allow the fitment of quick release couplings and after market steering wheels to non Air Bag cars. Suits quick release couplings with 70mm x 6 PDC fitment Bolts directly to the original steering wheel boss. Learn More

Two Phosphor Bronze Cups for the Aluminium Steering Rack. The Bronze cups are a direct replacement for the standard Nylon cup, which can fail in extreme cicumstance such as heavy track work with sticky tyres. Learn More

Steering Column Lower Shaft and Universal Joints Equivalent to Lotus part number D111H0003F Fits all S1, S2K, S2 Toyota, Europa, etc etc Comes complete with the correct high grade nuts and bolts (3 bolts 3 nuts) Learn More

Steering Arm / Upper plinth Bolt Kit. On the S2 Elise and Exige, Lotus upgraded the bolts that are used in the Steering arms on the front suspension and the Top Ball Joint Plinths on the rear suspension from 8.8 to 10.9. This kit of 10.9 cap head bolts are a must for anyone driving there S2 on the circuit. (The S1 cars with alloy uprights use 8.8 grade bolts for the steering arms and top ball joints) 4 bolts for the two front steering arms 4 bolts for the two rear top ball joint plinths Learn More

Wishbone Bushes. Lotus supply three differant bushes for your wishbones, 4 short in the rear suspension lower arm front pivot (2 pairs) 2 Long in the front suspension upper arm rear pivot. (soft) 12 Long in the remaining pivots (standard hardness) Our bushes do not have the 'soft' bush as we found a slight improvement in the control of the cars geometry by fitting the slightly harder bush in all the pivot points.However we can supply the soft Lotus bush should it be required! Our bushes are ideal to repalce standard bushes or an upgrade, when the harshness of solid type bushes is not desireable! Learn More

Wishbone Bush Kit. A complete wishbone bush kit consisting of 14 Long and 4 Short Seriously Lotus bushes. These bushes are a cost effective alternative to the expensive OE Lotus bushes. Lotus supply three differant bushes for your wishbones, 4 short in the rear suspension lower arm front pivot (2 pairs) 2 Long in the front suspension upper arm rear pivot. (soft) 12 Long in the remaining pivots (standard hardness) Fits all 4 cylinder Elise and Exige models as well as VX220 and Europa etc Our kit does NOT have the 'soft' bush as we found a slight improvement in the control of the cars geometry by fitting the slightly harder bush in all the pivot points. Our bushes are ideal to repalce standard bushes or an upgrade, when the harshness of solid type bushes is not desireable! Learn More

Applications - All S2 (Toyota) Elise/Exige/2-Eleven (Not 2010 cup cars) This Seriously Lotus Shear Panel has been designed to fit with the larger capacity baffled Pro-sump. (Will also fit with the standard sump) It reduces longitudinal and lateral compliance of the rear suspension, increasing lateral hub stiffness and tyre contact patch stiffness, therefore maximising vehicle potential on the circuit. Including the fitting kit this shear panel weighs an incredible 0.8kg 210mm wide, 590mm long with 20mm sides This shear panel fits underneath the engine/gearbox and connects the chassis and rear of the subframe. Simple bolt on modification for those who enjoy circuit driving. For those with the Lotus shear panel already fitted that wish to upgrade to a Pro-sump, then this is an ideal modification. Simply remove the Lotus Shear Panel and replace with this Seriously Lotus version. (It used 6 of the 8 mounting points used by Lotus),. We have designed this panel so that it is fully interchangeable with the Lotus Shear Panel but allowing the fitment of our baffled sump (a must for circuit use) A significant added benefit of this panel is the fact that when changing the oil filter this panel does not need to be removed/ cleaned due to spilt oil. Access to the oil filter is the same as without the panel fitted (Unlike the Lotus version) Learn More

S3 Elise Hub / Wheel Bearing for cars with ABS. (Complete with speed sensor) High quality SFK bearing pack as used by lotus Same as Lotus part number A120D6009F Lotus price £118.00 + vat For cars with Bosch ABS system (All S3 Elise, also S2.5 2011 MY) Learn More

A pair of steering rack gaitors for all models of Elise and Exige fitted with the Sona steering rack (All Toyota engine Elise and Exige models) Equivalent to lotus part number A120H6004S A120H6005S These gaitors are a direct replacement for the original parts as used by lotus. They are not an of the shelf part that is larger than the original part Complete with four nylon tie wraps Supplied as a pair Learn More

S2/S3 Sona Steering Rack Service Kit 2 X Steering rack tie rods 2 X Rack boots/Gaitors Plus the option of adding two track rod ends Learn More

S2/S3 Elise and Exige Steering Rack Toe link Rod Parts for the Elise and Exige Sona steering rack have been unavailable until now! Replacement racks from Lotus are over £700. A common failure on these racks is the joint at the inner end of the track rod, meaning a replacement rack is needed to pass the MOT At last here is a cost effect repair part for these steering racks, supplied singularly (Two require per vehicle) Fits all Elise and Exige models fitted with the Sona steering rack (All Toyota engine Elise and Exige models) Learn More

S2 Toyota Toe Link Kit (Tapered Uprights) Toe link kit for all Toyota engined Elise, Exige and 2Eleven (4 Cylinder cars, NOT V6) Learn More