Braking

Exige V6 Front Floating Bell Upgrade Kit A floating bell upgrade kit for cars already fitted with two piece front brake discs. Designed to be installed with the factory supplied two piece brake rota. The kit consists of the following parts 2 x Alloy floating bells 24 Titanium drive bobbins 24 Nuts / bolts 12 x Anti rattle clips Learn More

Exige V6 Handbrake Cable Lotus part number A138J0034F Learn More

Genuine Lotus Exige V6 J hook front and rear brake discs (All Four Discs) Front discs 332mm x 32mm A138J4021F A138J4022F Rear Discs 332mm x 26mm A138J4023F A138J4024F Learn More

Genuine Lotus Exige V6 J hook front brake discs (Pair) 332mm x 32mm A138J4021F A138J4022F Learn More

Genuine Lotus Exige V6 J hook rear brake discs (Pair) 332mm x 26mm A138J4023F A138J4024F Learn More

Motorsport and safety feature at the same time: Our newly developed Ko-Bra Race ABS and ESP! The 1st available motorsport ABS / ESP on the market especially developed for the Exige and It has and extensively tested. Komo-Tec's many years of experience in motorsport, the knowledge of the Exige range itself and the feedback from customers have made it possible to work and point out the essential points for development and optimization. The result is a genuine plug'n'play solution, It does not require additional sensors and wiring looms, It uses the cars current sensors and wiring. The system is just as suitable for everyday sporting use as it is for ambitious use on the track! The existing Lotus-DPM functions of the driving modes (Tour, Sport, Race and OFF) could be integrated and expanded. So if you make the effort to use the system right, you will definitely be faster and safer! ABS: In the future, the limiting factor for you will (almost) be the choice of tires only! Typical racing deceleration forces ​​of over 2g are possible now! Even when braking deep into the curve, the typical understeering of the standard brake is eliminated and enables precise steering through an optimal ratio between the maximum possible braking and lateral force control. The so-called ice mode (“hard brake pedal”) is prevented. ESP: An ESP works through selective brake intervention and regulation of the engine torque. The lower torque in particular causes a considerable interruption in power. Thanks to our adapted regulation, you control the torque by the accelerator pedal only. The control allows higher drift angles and also power slides. Twists are still effectively prevented and corrected more gently. It is still possible to switch off the ESP completely - but it is no longer necessary for a hot lap time as overcompensating brake interventions no longer take place. EDS: The electronic limited slip differential is no longer activated in the software to relieve the brake on the rear axle and protect it from overheating. However, we recommend a limited slip differential. TC: The traction control is also no longer activated in the software in order to achieve better traction and full access to the engine torque. Variable Settings: A previously unavailable option is added. You can use variable settings via the Lotus Mode selection-button. These can be adapted to the typical tyre types used (road / rain, semi-slick, slick), see pictures. Data recording: All variables relevant to driving dynamics are made available via CAN bus and can be recorded via CAN logger (not included in the offer). This ABS/ESP unit can be used on: Exige V6s, Cup V6, Sport 350, Cup 360, Sport 380, Cup 380, Sport 410, Cup 430 Motorsport part. Price includes installation at our workshop in East Yorkshire (NOT AVAILABLE FOR DELIVERY) Learn More

Exige V6 OEM Front Brake Discs Genuine Lotus parts Supplied as a pair Lotus part numbers:- A138J0014F A138J0015F Learn More

4 Replacement brake pads pins for the Exige V6, Evora and Evora 400 Learn More

FCR Bracket (2 pot on rear of an S2 or S3 4cyl car) Two aluminium mounting brackets to allow the 2 pot front caliper to be mounted on the rear of any S2 , S3 4Cylinder car or VX220 whilst retaining the original caliper for use as a hand brake. To complete the installation you will need to source:- 2 x 2 pot front calipers including brake pads 4 x caliper mounting bolts 2 x brake hoses brake fluid as necessary Track use only. Learn More

Fixed Alloy Disc Bells (S2) These fixed brake bells have a disc mounting pcd of 177.8 so can be used with most popular brake discs. Aluminium fixed disc bell billet machined in 7075-T6 and Hard Anodised. (Originally design by Nitron) These bells weigh an amazing 600 grams Even when attached to our 308mm Alcon brake rota's (which only weigh 4.5kgs) they are still only 5.3kgs Inc the bolts (A standard S2 Lotus disc is over 5.9kgs) Learn More

Floating Bell Anti Rattle Spring Kit 12 Anti rattle spring clips for the AP racing floating bells as used by Lotus on the Exige 360 Cup and 3Eleven etc 12 clips (6 on each disc) 12 clips for one pair of discs Learn More

Floating Bell Service Kit. 12 x Titanium Bobbins 12 x correct Nuts Bolts and washers Two kits needed for a pair of discs Learn More

EACH KIT IS FOR ONE CALIPER TWO KITS NEEDED PER CAR Front caliper brake pad fitting kit for the standard Lotus two pot caliper. Kit includes 2- caliper/pad pins 2- R clips 1- anti-rattle shim Learn More

Front Brake Pads (2 pot) Ferodo 2500 Learn More

Goodridge Braided Brakes hoses for all 4 cylinder models of Elise and Exige, VX220, Europa, 340R, 2Eleven Etc A very good upgrade for any car used on the road or track. With age, the rubber hoses fitted by lotus become soft and perish replacing them with a set of these Braided Hoses will gives a much firmer and more consistent feeling to the brake pedal. 4 Hoses supplied in each kit Learn More

Goodridge Stainless Brake Hoses (2) 4 Pot Calipers A pair of replacement Goodridge brake hose with stainless ends and fittings for calipers that use a Banjo style fitting For S2 Exige with 4 pot calipers etc etc.( NOT for V6 Exige or Evora) Learn More

Handbrake cable all S2/S3/VX220 4 Cylinder cars Lotus part number A120J0039F Learn More

4 Replacement Lotus / AP Racing 4Pot Caliper Pad Pins CP7635 Caliper retaining pin (Direct fit caliper, No bracket) Equivalent to Lotus part number A120J6025S Lotus price for 4 pins £31.80 For S2 Elise and Exige with 4 pot front calipers (Not for V6 Exige or Evora) Learn More

Lotus S1 Front AP 2 Piston Caliper Piston Price is for a single 2 piston caliper piston, 2 required per caliper. Specific piston for S1 Elise front caliper fitted with the anti push back spring Learn More

Lotus S2 onwards/VX220 Front AP 2 Piston Caliper Piston Price is for a single 2 piston caliper piston, 2 required per caliper. Fits all 2 piston AP front calipers from S2 K series cars onwards Learn More

Lotus sport developed big brake upgrade for the S2 Elise,Exige This kit consists of the following parts:- AP Racing/Lotus direct fit four pot calipers (No brackets necessary) Matching front and rear brake pads Two one piece handed 308mm discs (4 stud) Four braided brake hoses Caliper mounting bolts DOES NOT INCLUDE BRAKE FLUID This brake kit will fit inside a standard Lotus 16 inch (5.5 wide) wheel but DOES need careful positioning of the wheel balance weights All the major parts needed to upgrade the braking system of an S2, Europa S or VX220 to the same as that fitted to the 2010 Exige with the sport pack brake kit or the Europa SE (Just add brake fluid) Developed by the people who designed the car. Learn More

Lotus/VX220/ Front 2 Piston Caliper Seal Kit Set of 4 seals for a single caliper. To replace seals in both calipers will require 2 kits. Learn More

Front brake pads manufactured by Mintex, a well respected OEM supplier of automotive parts. These brake pads are a very cost effective replacement for standard cars which are used on the road as well as on the circuit. Mintex 1144 material works well from cold and offers a good first upgrade to the brakes of any Elise, Exige or VX220. For all S1,S2,S3 Elise and S1,S2 Exige with standard 2 pot front calipers (Not for 4 pot AP Racing calipers) Learn More

Rear brake pads manufactured by Mintex, a well respected OEM supplier of automotive parts. These brake pads are a very cost effective replacement for standard cars which are used on the road as well as on the circuit. Mintex 1144 material works well from cold and offers a good first upgrade to the brakes of any Elise, Exige or VX220. For all S1,S2,S3 Elise and S1,S2 Exige with standard brembo rear calipers. Learn More