Full Catalogue

SL Harness Bar New updated design, Now also fits cars with factory carbon seats Easy Installation (<1hr) Installs directly to factory threaded mounting points. No removal or cutting of the rear bulkhead trim or seats. Powder-coated black. Fits:- Toyota powered Elise and Exige (S2-S3) V6 Exige S2 Rover cars with short roof Learn More

Wishbone Bushes. Lotus supply three differant bushes for your wishbones, 4 short in the rear suspension lower arm front pivot (2 pairs) 2 Long in the front suspension upper arm rear pivot. (soft) 12 Long in the remaining pivots (standard hardness) Our bushes do not have the 'soft' bush as we found a slight improvement in the control of the cars geometry by fitting the slightly harder bush in all the pivot points.However we can supply the soft Lotus bush should it be required! Our bushes are ideal to repalce standard bushes or an upgrade, when the harshness of solid type bushes is not desireable! Learn More

Wishbone Bush Kit. A complete wishbone bush kit consisting of 14 Long and 4 Short Seriously Lotus bushes. These bushes are a cost effective alternative to the expensive OE Lotus bushes. Lotus supply three differant bushes for your wishbones, 4 short in the rear suspension lower arm front pivot (2 pairs) 2 Long in the front suspension upper arm rear pivot. (soft) 12 Long in the remaining pivots (standard hardness) Fits all 4 cylinder Elise and Exige models as well as VX220 and Europa etc Our kit does NOT have the 'soft' bush as we found a slight improvement in the control of the cars geometry by fitting the slightly harder bush in all the pivot points. Our bushes are ideal to repalce standard bushes or an upgrade, when the harshness of solid type bushes is not desireable! Learn More

Applications - All S2 (Toyota) Elise/Exige/2-Eleven (Not 2010 cup cars) This Seriously Lotus Shear Panel has been designed to fit with the larger capacity baffled Pro-sump. (Will also fit with the standard sump) It reduces longitudinal and lateral compliance of the rear suspension, increasing lateral hub stiffness and tyre contact patch stiffness, therefore maximising vehicle potential on the circuit. Including the fitting kit this shear panel weighs an incredible 0.8kg 210mm wide, 590mm long with 20mm sides This shear panel fits underneath the engine/gearbox and connects the chassis and rear of the subframe. Simple bolt on modification for those who enjoy circuit driving. For those with the Lotus shear panel already fitted that wish to upgrade to a Pro-sump, then this is an ideal modification. Simply remove the Lotus Shear Panel and replace with this Seriously Lotus version. (It used 6 of the 8 mounting points used by Lotus),. We have designed this panel so that it is fully interchangeable with the Lotus Shear Panel but allowing the fitment of our baffled sump (a must for circuit use) A significant added benefit of this panel is the fact that when changing the oil filter this panel does not need to be removed/ cleaned due to spilt oil. Access to the oil filter is the same as without the panel fitted (Unlike the Lotus version) Learn More

Seriously Lotus 4 Pot 308mm Floating Disc Brake Upgrade Kit (All S2 Toyota cars) Buy sourcing all the best components from the leading brake manufacturers we have put togarther the very best 4 pot upgrade kit for your S2. Buy using the Lotus - AP racing calipers the correct piston size for the cars brake master cylinder is maintained This kit consists of the following parts:- 2 x AP Racing/ Lotus direct fit four pot calipers (No brackets necessary) Matching front and rear brake pads (Ferodo 2500) 2 x Seriously Lotus/Nitron floating alloy bells with titanium bobbins and high quality A P Racing bolts, 2 x 308mm Alcon Vented Discs 4 x Braided brake hoses Caliper and disc mouting bolts and screws Your car will need the wider Exige S2 size wheels for this kit to fit. This brake kit will NOT fit inside a standard Lotus 16 inch (5.5 wide) wheel. Everything needed to upgrade the braking system of an S2, If you use your car on the track we have added the option of using any of the following brake pad materials as an upgrade Pagid RS4-2 Carbone Lorraine RC5+ Carbone Lorraine RC6 We can also offer an upgrade to Castrol SRF brake fluid. Learn More

Seriously Lotus 4 Pot 308mm Brake Upgrade Kit (All S2 Toyota cars) Buy sourcing all the best components from the leading brake manufacturers we have put togarther this very cost effective 4 pot upgrade kit for your S2. Buy using the Lotus - AP racing calipers the correct piston size for the cars brake master cylinder is maintained This kit consists of the following parts:- 2 x AP Racing/ Lotus direct fit four pot calipers (No brackets necessary) Matching front and rear brake pads (Ferodo 2500) 2 x Nitron fixed alloy bells with bolts, 2 x 308mm Alcon 2 x Braided brake hoses Caliper and disc mouting bolts and screws Your car may need the wider Exige S2 size wheels for this kit to fit. This brake kit will NOT fit inside a standard Lotus 16 inch (5.5 wide) wheel. Everything needed to upgrade the braking system of an S2, If you use your car on the track we have added the option of using any of the following brake pad materials as an upgrade Pagid RS4-2 Carbone Lorraine RC5+ Carbone Lorraine RC6 We can also offer Castrol SRF brake fluid. Learn More

FIA & ECE Homologated 4-point belt with ASM. 3" shoulder belt, 2" lap belt pull-down Elise (S1, S2, 111R), Exige (S1, S2), 340R Exige V6s,350.410. FE Buckles are road legal and FIA approved. 4pt Harnesses are recommended for use with competition type seats which normally have slots in the seat backs to allow free passage of the harness. Certain high back, integrated headrest seats are not suitable for use with 4pt harnesses. Profi II (2" lap belt) in BLACK 4 point belt with wrap attachment 3” shoulder belts FE road style buckle asm (anti sub) Right hand or Left hand Learn More

FIA Homologated 4-point belt with ASM. 3" shoulder belt, 2" lap belt pull-down Elise (S1, S2, 111R), Exige (S1, S2), 340R Exige V6 etc 4pt Harnesses are recommended for use with competition type seats which normally have slots in the seat backs to allow free passage of the harness. Certain high back, integrated headrest seats are not suitable for use with 4pt harnesses. Profi II (2" lap belt) in BLACK 4 point belt with wrap attachment 3” shoulder belts FE road style buckle ASM (anti sub) Right hand or Left hand SPECIAL ORDER Learn More

S3 Elise Hub / Wheel Bearing for cars with ABS. (Complete with speed sensor) High quality SFK bearing pack as used by lotus Same as Lotus part number A120D6009F Lotus price £118.00 + vat For cars with Bosch ABS system (All S3 Elise, also S2.5 2011 MY) Learn More

A pair of steering rack gaitors for all models of Elise and Exige fitted with the Sona steering rack (All Toyota engine Elise and Exige models) Equivalent to lotus part number A120H6004S A120H6005S These gaitors are a direct replacement for the original parts as used by lotus. They are not an of the shelf part that is larger than the original part Complete with four nylon tie wraps Supplied as a pair Learn More

S2/S3 Sona Steering Rack Service Kit 2 X Steering rack tie rods 2 X Rack boots/Gaitors Plus the option of adding two track rod ends Learn More

S2/S3 Elise and Exige Steering Rack Toe link Rod Parts for the Elise and Exige Sona steering rack have been unavailable until now! Replacement racks from Lotus are over £700. A common failure on these racks is the joint at the inner end of the track rod, meaning a replacement rack is needed to pass the MOT At last here is a cost effect repair part for these steering racks, supplied singularly (Two require per vehicle) Fits all Elise and Exige models fitted with the Sona steering rack (All Toyota engine Elise and Exige models) Learn More

S2 Toyota Toe Link Kit (Tapered Uprights) Toe link kit for all Toyota engined Elise, Exige and 2Eleven (4 Cylinder cars, NOT V6) Learn More

S2/S3 4 Cyl Drilled brake discs (Sold as a Pair) A pair or discs that are a direct replacement for any standard S2 drilled brake disc. These brake discs have curved vanes which are handed left and right to ensure balanced cooling accross both sides of the car, unlike the original discs which use one casting and have curved vanes all in the same direction. This leads to one side of the cars brakes being cooled better than the other!!! Many of the aftermarket discs that are available also use one casting with vanes which are in one direction only! Then they have grooves or holes put onto the disc to make them handed. Our discs use handed castings and should not be confused with other products on the market. Produced here in the UK Diameter = 288mm Thickness = 26mm Braking surface = Drilled Disc type = Vented Vanes = Curved, handed left and right Learn More

S2/S3 4 Cylinder cars brake discs These brake discs have curved vanes which are handed left and right to ensure balanced cooling accross both sides of the car, unlike the original discs which use one casting and have curved vanes all in the same direction. This leads to one side of the cars brakes being cooled better than the other!!! Many of the aftermarket discs that are available also use one casting with vanes which are in one direction only! Then they have grooves or holes put onto the disc to make them handed. Our discs use handed castings and should not be confused with other products on the market. Diameter = 288mm Thickness = 26mm Braking surface = Plain / undrilled Disc type = Vented Vanes = Curved, handed left and right Learn More

S2/S3 4 Cyl Alloy Belled Brake Discs A pair of alloy bells and Drilled discs to fit all models of S2/S3 using the standard 288mm discs. These are a direct replacement without any modifications. Anodised bells (Titanium in colour) These are the very best value and quality alloy belled disc available for the S2! Unlike many brake discs for the S2, these have the correct cooling vane orientation for each side of the car. Supplied with AP Racing bolts nuts etc etc Improve the braking and looks of your car with these Brake Discs.... Discs rota's also available seperately, so no need to replace the bells with each set of new discs. Standard S2 discs are between 5.9 kgs and 6.0 kgs These alloy belled discs are 5.6 kgs Priced and supplied as a pair of discs Learn More

4 Counter sunk screw to secure the brake disc to the hub as used on ALL S2 Elise and Exige and also S3 Elise. M6x16 As these screws are purely for alignment purposes (They keep the disc aligned to aid wheel bolt fitting when changing a wheel), they are made from stainless steel. This helps to stop the screw becoming seized. 4 screw with each order (4 required per car) NOT EVORA OR EXIGE V6 Learn More

S2 Wheel Stud Conversion Kit Learn More

S2 Toyota Toe Link Kit With Cross brace(Tapered Uprights) Learn More

16 Splined wheel bolts with a moving washer and a splined tool. Learn More

16 Splined wheel bolts and a splined tool. Learn More

16 Splined wheel bolts and a splined tool. Learn More

S2 Oil Cooler Radiator (Toyota) Genuine Lotus replacement oil cooler radiator. As fitted to all Toyota cars with factory fitted oil coolers. The RH Radiator can also be used to upgrade cars fitted at the factory with just one oil cooler Lotus part numbers RH A120K0020F LH A120K0021F Learn More

S2 K Series Toe Link Kit (Later K Series Cars With Tapered Uprights) Learn More